Author Archives: Michal Necasek

Learn Something Old Every Day, Part II

Posted on July 17, 2021 by Michal Necasek

The ultimate reason why I pulled out the old Seagate ST-225 drive was because I wanted to try connecting it to the Western Digital WD1003-IWH board that I recently acquired. The WD1003-IWH is a curious evolutionary half-step between ST506 interface … Continue reading →

Posted in IDE, PC hardware, PC history, Storage | 11 Comments

Learn Something Old Every Day

Posted on July 14, 2021 by Michal Necasek

More or less by accident I found myself writing a very basic DOS utility to read data off of an IDE drive. It started out by just issuing the IDENTIFY DRIVE command and capturing the data, but adding the ability … Continue reading →

Posted in Documentation, PC hardware, PC history, Seagate, Storage | 3 Comments

Dirty Work

Posted on July 9, 2021 by Michal Necasek

As I’m slowly archiving my giant pile of floppies, I naturally come across specimens that have one kind of problem or another. After going through hundreds of floppies, I can safely say that 3½″ floppies are much less prone to … Continue reading →

Posted in Archiving, Floppies | 5 Comments

Centaur Close-ups

Posted on July 2, 2021 by Michal Necasek

Readers have expressed interest in seeing what exactly a Western Digital ‘Centaur’ drive looked like. I took a few photos of a WD95044-A drive, the larger capacity (40 MB) and newer variant of the WD Centaur family. Some photos were … Continue reading →

Posted in PC hardware, PC history, Storage, Western Digital | 4 Comments

Recalibration Needed

Posted on June 25, 2021 by Michal Necasek

The OS/2 Museum recently acquired two horribly slow old Western Digital IDE drives model WD93044-A. These were WD’s first foray into IDE hard disks, combining a rather outdated Tandon RLL drive chassis (3.5″ half-height stepper drives) with WD’s own controller … Continue reading →

Posted in Bugs, IDE, Western Digital | 32 Comments

Can This Conner Talk?

Posted on June 18, 2021 by Michal Necasek

As part of research into the IDENTIFY DRIVE command, the OS/2 Museum acquired two old Conner IDE drives, a CP-342 and a CP-341i. These drives look extremely similar at first glance, and they’re both 40 MB IDE drives, but on … Continue reading →

Posted in Conner, Debugging, Hardware Hacks, Storage | 19 Comments

OS/2 6.304: Who Has More?

Posted on June 11, 2021 by Michal Necasek

Yet another interesting item that I recently ran through a Kryoflux is a set of 30 floppies labeled “IBM OS/2 Version 2.0 Pre-release Evaluation Copy – 6.304”. In this case, there’s no mystery as to what it is: 6.304 was … Continue reading →

Posted in Archiving, IBM, OS/2, Pre-release | 8 Comments

EISA Specification 3.1

Posted on June 9, 2021 by Michal Necasek

While researching the Compaq Intelligent Drive Array (IDA), a circa 1990 EISA-based IDE RAID controller, I quickly established that there’s very little surviving information about it, and most of what there is can be found in two or three patents … Continue reading →

Posted in Documentation, EISA | 19 Comments

WD1007V Commands

Posted on June 5, 2021 by Michal Necasek

While researching material for a previous article, I wanted to examine the only AT-compatible ESDI controller I have, a Western Digital WD1007V-SE2. My board was made in 1990, the firmware is from 1989, and the controller was likely introduced in … Continue reading →

Posted in Debugging, Documentation, ESDI, Western Digital | 6 Comments

Whence IDENTIFY DRIVE?

Posted on June 4, 2021 by Michal Necasek

As most everyone knows, the AT Attachment standard (informally known as IDE) started by literally bolting the previously standalone AT disk controller onto a MFM drive with a ST506 interface and connecting the assembly to the host system with a … Continue reading →

Posted in Compaq, Documentation, IDE, PC hardware, PC history, Storage | 38 Comments